Troubleshooting a Hot Water System Failure: What to Do If It Ceases Working
Troubleshooting a Hot Water System Failure: What to Do If It Ceases Working
Blog Article
We have stumbled on this article on What Would Cause My Electric Water Heater to Stop Working? down the page on the internet and thought it made good sense to discuss it with you in this article.
Lots of modern-day residences make use of an electrical hot water heater for their furnace, because of its benefit and also convenience of use. However, much like any other electric devices, troubles may occur with its use, all of a sudden. It can be truly frustrating to wake up to a cold shower instead of a warm one or having your bath with water that isn't warm enough or even too warm. Whatever the situation might be, hot water heater issues can be fairly stressful. Thankfully, we've made a list of possible solutions to your hot water heater problems. There are a variety of aspects that might trigger a lot of these problems, maybe a concern with the power supply, the electrical burner, or the thermostat. Prior to doing anything, guarantee you shut off the main power supply for safety. Whatever the problem is, getting it repaired should not posture excessive of a problem if you follow these actions:
Examine Your Power Supply:
As standard as this might seem, it is very necessary. Without ample power, your water heater will certainly not function. So the first thing to do when your water unexpectedly stops working is to validate that it isn't a power trouble. Examine if the fuse is blown out or the circuit breaker stumbled. If the breaker is the issue, simply transform it on and off again. Replace any kind of broken or damaged fuse. Test the home appliance with power after these modifications to see if it's now functioning.
Check the Heating Element in the Hot Water Heater:
If it's not a power issue, after that attempt taking a look at your heating element if it is still functioning. Check each of your burner to make sure the issue isn't with any one of them. If any one of them is malfunctioning, change that component and then inspect whether the warm water is back on.
Examine Your Thermostat:
If your hot water heater still isn't working or the water appearing isn't warm enough, you may need to examine the temperature settings on your top thermostat. Guarantee the breaker is switched off prior to doing anything. Open the access panel and also press the red button for temperature reset over the thermostat. This must help heat the water. Turn the circuit breaker back on as well as check if the issue has actually been solved.
Call A Professional:
If after replacing all damaged parts and resetting your temperature level, the hot water heater still isn't functioning, you might need to call a specialist plumber for an expert viewpoint. The trouble with your heating system could be that the cold and hot faucets have been changed or it may be undersized for the quantity of hot water required in your home. Whatever the situation may be, a specialist plumber would certainly assist address the problem.
Conclusion
Hot water heater problems are not constantly major. Most of them result from minor issues like a blown fuse or damaged heating element. Changing the damaged components ought to do the trick. Nevertheless, if you are still not able to resolve the problem, give a call to your local plumber to come to get it repaired.
8 possible reasons why you have no Hot Water
Along with streaming Netflix and having light flood a room when we flick a switch, having hot water flow from our taps and showerheads whenever we want is an oft-overlooked modern miracle of homeownership. That's why, when that flow goes cold, it can be shocking — and not just in a "Wow, that's freezing" kind of way while you're in the shower.
Water Leak
Before hot water reaches your taps and showerheads, it needs to spend some time in your water heater. This appliance, which can be either gas- or electric-powered, takes the cold water that enters your home from your well or utility company and cooks it until it gets hot. It's akin to an electric tea kettle.
Obviously, if your water heater is leaking, it will never fill with water so it won't have anything to warm. To see if this is the case, simply examine the area around the water heater to see if it is wet. If so, you'll likely need to replace the unit, but you can also call in a pro for a second opinion and to see if it is fixable. Sometimes leaks can happen around fixtures on the water heater, and if so, the solution might be as simple as replacing them.
Gas Heater: Gas Leak
If your hot water is fueled by natural gas and there is a leak in the supply line or where the line enters the tank, the appliance won't have the power it needs to heat up your water. The result is not only inconvenient, but it can be extremely dangerous as well. If you smell gas when you investigate your water heater, call your gas utility company immediately and report it as an emergency. It might also be prudent to leave your home until a repair person from the company arrives. Your utility company will usually fix any kind of gas leak. However, in terms of getting your water heater working again, you'll need to relight the pilot and wait a while to see if it is functioning properly. You can call in a water heater specialist or plumber to help with this.
Gas Heater: Pilot Light Problems
There are two other issues with gas-powered water heaters that can lead to a loss of hot water. The first is a pilot light that's blown out. The pilot light is the source of a constant flame inside your water heater. When the heater determines the need to heat up the water it is holding, it will open a valve that will cause gas to flow over the pilot light and cause it to ignite. To see if your pilot light is functioning, there is usually a small window in the front of the water heater. If you can't see a flame, remove the access panel and see if that helps you locate it. If there is still no flame, you'll need to relight it in accordance with the manufacturer's instructions.
Your pilot light should burn with a bright blue flame. If not, make sure there are no drafts affecting it, which could keep it from functioning properly. If the flame looks yellow, it might be a sign of the presence of carbon monoxide, which spells trouble and needs to be looked at right away by a technician.
Gas Heater: Faulty Thermocouple
The second reason why a gas-powered water heater might fail is a faulty thermocouple. This is a small probe that should sit in the pilot light flame. Its purpose is to stop the flow of gas if it senses that the pilot light is out. Sometimes, these probes get knocked off track, so make sure it is directly in the flame. They can also get a buildup on them that prevents their function, so try cleaning yours off with some steel wool or fine-grit sandpaper. If your pilot light won't stay lit and you've tried these steps to fix the thermocouple, it is likely faulty and needs to be replaced. Call a technician.
Electric Heater: Breaker Blues
Electric water heaters don't have pilot lights, because there is no gas to burn in order to heat up the water. Instead, they do their magic through the use of (naturally) electricity. But that's not to say things can't go wrong with them. If your electric water heater isn't working properly, there's a good chance that a breaker was tripped that supplies the appliance power. Check your breaker box and flip any breakers that have switched to the off position back on. If it trips again, then there might be a fault in the water heater, and you'll want to call in a pro to have a look.
Electric Heater: Reaching The Limit
If the breaker is fine, check to see if the high-temperature limit has switched off on the water heater itself. To do so, first turn off the breaker to the unit. Then remove the service panel and press the red button you'll find there. This is the limit switch, and resetting it could solve your problem. To check, replace the panel, turn the breaker back on and listen to see if the water heater is functioning again.
Electric Heater: Heating Element
If these steps don't fix the issue, then you might have a failed heating element, which will need to be replaced. Unless you are comfortable with such repairs, calling in a technician might make the most sense.
https://www.homeserve.com/en-us/blog/home-improvement/no-water-heater/
We had been brought to that report on How to Troubleshoot and Repair an Electric Water Heater from an associate on another blog. Those who enjoyed our article if you please do not forget to share it. I treasure reading our article about What Would Cause My Electric Water Heater to Stop Working?.
Efficient, reliable plumbing services here. Report this page